| 耐冲压金属油墨系列 适用于各种金属、玻璃、陶瓷、石材、电镀(含水电镀)、阳极氧化铝表面、静电喷漆面及烤漆面等制品的丝印及移印，不需加固化剂，不需烘烤，即可获得优异的附着力。油墨特性：1、平光(如需亮光请选择我司JL系列)、附着力佳、耐酒精、耐化学品；2、手感好，流平性佳、面光洁；3、表面硬度好，耐冲击性能强、抗刮伤；4、耐酒精、耐化学品程度佳；印刷：选用网目为100-420目，以120T聚酯单丝、感光胶网版计算涂覆盖面积每公斤达35~40㎡。表干时间自然挥发5-10分钟，实干时间在24小时以内，48小时后达*佳性能。1.用B-03专用稀释剂开油水2.用718洗网水洗网。3.可选择添加JS-9硬化剂10%用于增加油墨附着力及物理化学抗性。4.烤箱80℃烘烤30分钟佳能更优。测试方法(完全干燥后)：1.3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。2.纯度99%的酒精500G力在油墨表面来回擦拭200次无脱色。使用方法：1.使用前应充分搅拌，用后随时密封。2.搅拌时先加固化剂静置10分钟后，再加稀释剂10-15%，稀释到印刷粘度。3. 加入固化剂的油墨使用时限为4-6小时，过期请弃用，剩余油墨不可回收。4.网版塞网时可用洗网水清洗。5.不得与其它类型油墨混合使用。注意事项：1.各种物料的外观相似，但可能会是不同的材料，客户需先试印，确其符合要求后，再批量生产。2.在移印过程中，如出现拉丝或散开现象，可适当加入一些慢干膏即可。3.环境温度过高，将会影响油墨原有质量。4.请远离火源，避光保存。 Resistance to stamping metal ink series in the application of metal, glass, ceramic, stone, electroplating (water cut electroplating), anodic alumina surface, electrostatic spray paint surface and paint surface and so on screen printing products and pad printing, not needing curing agent, and does not need to bake, can obtain excellent adhesion. Ink features: 1, PingGuang (such as light please choose to our JL series), adhesion, good resistance to alcohol, resistance to chemicals; 2, feel is good, flow ping sex, good surface is bright and clean; 3 and fine surface hardness, impact resistance performance is strong, resistance to scratch; 4, resistant to alcohol, resistant to chemicals degree good; Printing: choose the mesh is 100-420 yard, and with 120 T polyester monofilament, photosensitive plastic nets edition calculation area covered with per kilogram of 35 to 40 ㎡. Dry time table natural volatilize 5-10 minutes, action in time within 24 hours, after 48 hours of optimum performance. 1. To use B-03 special thinner, open oil-water 2. With 718 wash nets washing nets. 3. Can choose to add JS-9-10 � and � � stiffening agent to increase physical and chemical resistance and adhesion of ink. 4. Preheat the oven to 80 ℃ bake 30 minutes more optimal Canon. |
免责声明： 以上所展示的信息由会员自行提供，内容的真实性、准确性和合法性由发布会员负责，企业录对此不承担任何责任。如有侵犯您的权益，请来信通知删除。